| Required Experience & Qualifications | 5 years Experience In Leak Repair Perform all duties as assigned by supervision including, but not limited to, the following as needed: - Possess the skills found in the leak repair skill register located at the end of this posting (the skills possessed will determine skill level and pay grade)
- Communicate/Coordinate with plant personnel in a professional and respectful manner
- Assess leaking component(s) and provide relevant information to supervisor and engineering
- Take field measurements of leaking component (ability to sketch and properly dimension non-standard components is a must)
- Competent use of the following measuring devices: Vernier calipers, OD calipers, ID calipers, circumference tape, measuring tape (able to read increments to 1/32), depth gauge, level, square, and angle finder
- Ability to adhere to Innovator Job Hazard Analysis (JHA) and Safe Work Procedures (Procedural non-compliance will not be tolerated)
- Conduct, and/or take part in, Field Level Risk Assessments and toolbox talks.
- Complete daily reports outlining the work activities
- Complete daily timesheets (LEMs) detailing the labour, equipment, and materials used during the work activities for each day
- Communicate daily activities with office personnel, promptly reporting issues, change in scope or change in field conditions.
- Communicate with co-workers in order to facilitate knowledge transfer, including ability to mentor junior technicians
|
| Other Information | Working Conditions:- Field duties require outdoor work in a plant atmosphere
- Interaction with other crew employees, as well as supervisors and client personnel.
- Working in plant and/or shop areas around production machinery with extreme noise levels.
- Exposure to live process leaks operating at high pressure/temperature
- Extreme working conditions ie/ very hot or frigid temperatures
- Work in confined space and IDLH atmospheres (relevant training, safeguards, and PPE to be provided)
- Ability to work from heights (including aerial work platforms, ladders, towers, etc)
- Must be able to wear safety equipment as required by the safety department for personal protection (ie/ full body harness, SCBA, SABA, respirators, chemical suits, steam suits, bunker gear, etc.)
- Camp accommodations will be supplied on a rotation basis, if applicable.
- Will be required to travel out of town on a periodic basis.
- Frequent Travel to Work Sites, Work Truck Provide
- Overnight stays in hotels or company houses till project completion.
Physical Requirements: - Must be able to lift and carry 50 pounds.
- Sufficient clarity of speech and hearing or other communication capabilities, with or without reasonable accommodation, which permits employee to communicate effectively.
- Ability to sit or stand for prolonged periods of time with or without reasonable accommodation.
- Sufficient vision or other powers of observation, with or without reasonable accommodations, which permits employee to investigations.
- Sufficient manual dexterity with or without reasonable accommodation, which permit the employee to perform routine office duties.
- Sufficient personal mobility and physical reflexes, with or without reasonable accommodations to perform office duties and travel when necessary to off-site locations.
Leak Repair Technician Skill Register: - Drilling
- Tapping
- Peening
- Valve Packing Injection
- Wire & Peen injection
- Segmental Wire & Peen injection
- Wire Wrap and/or Cable Tensioning Injection
- Work on High Pressure Leaks (>600psi)
- Use of High Pressure Packing Gland (HPPG)
- Install & Inject Void Fill Enclosure
- Install & Inject Flange Clamp
- Install & Inject Tongue Clamp
- Install (and inject) Perimeter Seal Enclosure
- Perform Manual Pipe Crimp
- Perform Hydraulic Pipe Crimp
- Complete a Threaded Union Injection
- Complete a Valve Seat Injection
- Complete an Upstream Valve Kill
- Perform a Hot Stud Change-out
- Ability to create a proper bolt pattern in field
- Ability to use torque equipment
- Work on Flammable Service
- Use of grounding equipment for flammable service
- Work on Oxygen Service
- Preparation of equipment for work on Oxygen Service
- Proper Sealant Selection based on process conditions
- Ability to calculate a void volume in the field
Role and Responsibilities: - Perform site assessments/walkdowns/measure-ups, etc..
- Perform Field Level Risk Assessments and review with technician(s)
- Review JHAs with technicians on site prior to work
- Receive/review site permits and review with technician(s)
- Complete all safety related paperwork throughout the job (ie. BBOs, Impacts, toolbox talk, etc)
- Complete daily LEMs ensuring that all equipment, material, labour, and expenses are accounted for
- Use and maintenance of project equipment as per OEM specifications as well as Innovator procedures
- Complete work as per the procedure – contact Supervisor/Manager if procedure can’t be followed for any reason
- Report all near misses, incidents, etc. and participate in investigations under Management supervision
- Follow project execution plans
- Complete execution paperwork diligently and neatly (ie. Mob checklists, ITPs, Field Reports, etc)
- Complete Daily Ops for each day on site logging all activities for the shift paying particular attention to delays and events that impact Innovator productivity
- Mentor/train technicians- sign off on technician qualifications
- Work with Operations Coordinators to build proposals
- Create project specific Safety Score Card
- Maintain first class client relationships/Customer satisfaction
- Return equipment to shop, complete asset transfers back to inventory
- Competency in all of the On-Line Services
|
